// Tools

Chainsaws - Maintenance and Service

What are some general points I should know about maintaining and servicing chain saws? Routine maintenance and service can minimize the hazards of working with chain saws.

What are some general points I should know about maintaining and servicing chain saws?

Routine maintenance and service can minimize the hazards of working with chain saws.

requirement Follow the manufacturer's instructions for maintenance and repair in the chain saw operator's manual.
requirement Do not use a chain saw that is damaged or not adjusted properly. Before using it, have it repaired and adjusted according to the manufacturer's specifications.
requirement Use only replacement parts that are intended for the chain saw that you are using.
requirement Turn off the engine before attempting to make any adjustments, clean, do maintenance, or repair the chain saw.
administrative Take the chain saw to a chain saw service centre to be repaired by qualified staff if the repairs required are not described in the operator's manual. In any case, chain saws should be returned to a service centre periodically (every few months to a year, depending on the usage) to be inspected and serviced by technically trained staff.
administrative Follow proper storage procedures if the saw will not be used for some time. It may be necessary to drain the gas/oil mixture.
requirement Dispose of fuel appropriately.

What are some things that I should know about the engine?

context Keep the muffler, air intake filter clean, and the spark arrester in place.
context Remove and service the starter if the starter cord does not fully retract.
context Use the correct fuel (gasoline or a gas/oil mix) as recommended by the manufacturer. For fuel mixtures, mix gasoline and engine oil according to the manufacturer's recommendations. Too much oil will make the saw run "dirty"; too little oil will damage the engine parts.
context Do not use a saw that needs repair. Remove and replace any damaged parts as recommended by the manufacturer.

What should I know about the chain and guide bar?

requirement Check the chains for excessive wear and replace them when necessary.
requirement Repair or replace badly hammered links.
requirement If cutters need replacing, file them to the same length as the existing cutters.
requirement Replace the bar if nicked or distorted.
requirement Replace the bar and chain if the bar is damaged.
requirement Replace the worn or damaged drive sprocket before it damages the chain.
administrative Inspect the drive links, sprockets, cutters and track for damage:
requirement a flat file for adjusting the depth gauge
requirement a round file of uniform diameter for sharpening cutters and maintaining drive links
requirement Use the proper size files to sharpen the chain. Two files are necessary:
requirement Check depth gauges every third or fourth time you sharpen the chain.
requirement Keep the chain lubricated.
requirement Adjust the tension of the saw chain after it has been in use for five to ten minutes. The chain stretches as it heats up and requires adjustments at intervals throughout its operation. Do not adjust the tension or replace the chain while it is hot. Damage to the guide bar or crankshaft can occur when an overly tightened chain cools.

How do I adjust the chain tension?

A loose chain increases wear on drive sprockets, drive links, and the bar, which can endanger the operator if it climbs out of the track. A chain that is too tight will also increase wear on components.

context Shut off the saw.
context Wear gloves to avoid cuts.
context Loosen bar nuts.
context Rest the tip of the bar on a small piece of wood to hold the tip up.
context Tighten the chain by turning adjustment screws until the chain is snug against the bar but able to be turned freely.
context Tighten bar nuts for correct chain tension by pulling on bar upwards with a gloved hand or supporting it firmly from below.
context Check tension frequently and adjust as required.
context Make sure the chain rotates smoothly after tensioning.
context When adjusting chain tension, follow the manufacturer's instructions. General tips include:
context Clean out the chain-oil portal when maintaining the guide bar. Sawdust can block the delivery of oil to the cutting chain.

What should I know about chain brakes?

Refer to OSH Answers Chain Saws - Safe Use of Chain Saws for more information.

requirement Apply the chain brake with the saw held firmly in both hands and the engine running at operating power. If the chain does not stop running immediately, have the saw serviced. The CSA Standard Z62.1-15 (R2020) Chain Saws recommends that the average brake stopping time not exceed 0.12 seconds, and the maximum stopping time not exceed 0.15 seconds.
requirement Remove the brake housing periodically and clean out any dirt, oil or sawdust.
requirement Always test the saw and brake before cutting.

What should I know about chain lubrication?

requirement Always follow the manufacturer's instructions.
requirement Check that the chain is receiving oil.
requirement Use the correct grade and type of chain saw oil.
requirement Many chain saws are designed such that it will need lubrication at the same time the saw needs fuel. Always check the oil level and refill accordingly.
requirement Follow the manufacturer's instructions for refilling, including the sprocket, if present.